Developer & tinkerer.

Booting a GSI on the Pixel 1/1 XL


Getting a GSI

There are tons of different GSIs to try out. I used the Google one.

Preparing the device

The system_a and system_b partitions on the Pixel are too small for the GSI. Therefore, we must resize them.

  1. Put the device into bootloader mode.

This is done with power + volume down.

  1. Boot TWRP on the device.

Open up a terminal and use fastboot to boot the TWRP image on the phone.

fastboot boot twrp-3.4.0-0-marlin.img
  1. Backup the GPT

The partition table on the phone is called the GPT and it is a good idea to back this up in case you mess anything up later on.

adb shell sgdisk --backup=/data/gpt.bin /dev/block/sda
adb pull /data/gpt.bin .
  1. Resize the partitions

Now we delete the systen & userdata partitions and resize them.

This is the configuration I used.

adb shell sgdisk --delete=33 /dev/block/sda
adb shell sgdisk --delete=34 /dev/block/sda
adb shell sgdisk --delete=35 /dev/block/sda
adb shell sgdisk --new=33::+2560M --change-name=33:system_a /dev/block/sda
adb shell sgdisk --new=34::+2560M --change-name=34:system_b /dev/block/sda
adb shell sgdisk --new=35:: --change-name=35:userdata /dev/block/sda

2.5 GB System A & empty B partition

If you insist on saving space and don’t want to use OTA updates, you can just resize the system_b partition to 1KB. I’ve tested this but it’s a little risky.

adb shell sgdisk --delete=33 /dev/block/sda
adb shell sgdisk --delete=34 /dev/block/sda
adb shell sgdisk --delete=35 /dev/block/sda
adb shell sgdisk --new=33::+2560M --change-name=33:system_a /dev/block/sda
adb shell sgdisk --new=34::+1K --change-name=34:system_b /dev/block/sda
adb shell sgdisk --new=35:: --change-name=35:userdata /dev/block/sda

2 GB System A & B (stock)

If you ever want to revert back to stock, this is what you’d do.

adb shell sgdisk --delete=33 /dev/block/sda
adb shell sgdisk --delete=34 /dev/block/sda
adb shell sgdisk --delete=35 /dev/block/sda
adb shell sgdisk --new=33::+2G --change-name=33:system_a /dev/block/sda
adb shell sgdisk --new=34::+2G --change-name=34:system_b /dev/block/sda
adb shell sgdisk --new=35:: --change-name=35:userdata /dev/block/sda
  1. Format the /data partition

It’s a good idea to format the userdata partition now.

# sometimes TWRP mounts these
adb shell umount /data
adb shell umount /sdcard
adb shell mke2fs /dev/block/sda35
adb shell mount -t ext4 /dev/block/sda35 /data

Flashing the GSI

  1. Flash the system partition

Now, we push the system.img to the device and write it to the system_a partition. Even if you opted to keep the system_b partition, do not write it to the other partition yet.

adb push system.img /data/system.img
adb shell dd if=/data/system.img of=/dev/block/sda33
adb shell rm -f /data/system.img
  1. Resize filesystem to partition

To finish up, we run a filesystem check and then resize the image to the full size of the partition.

adb shell e2fsck /dev/block/sda33 -fy
adb shell resize2fs /dev/block/sda33

Finishing up

  1. Mount the system partition

Now we mount the system_a partition.

adb shell mount /dev/block/sda33 /system_root
  1. Extract libraries from factory image

The GSI will fail to boot if we don’t manually add some libraries to the system_a partition. We can do this by extracting them from the factory image from Google for the phone. You can get that image here.

Once you have the image downloaded, extract the zip. Inside there will be another zip called or similar. Extract that as well. Now you should have a system.img file. Now we must extract that.

I opted to use p7zip, although you could simply mount it or use something else, I was having issues mounting it.

7z x system.img -o out
  1. Transfer libraries to device

Now we transfer the libraries we extracted, to the device

cd out/system
adb push lib/ /system/lib/vndk-29
adb push lib/[email protected] /system/lib/vndk-29
adb push lib/ /system/lib/vndk-29
adb push lib64/[email protected] /system/lib64/vndk-29

Once the files are copied, we must fix their permissions.

for i in \
    lib/vndk-29/ \
    lib/vndk-29/[email protected] \
    lib/vndk-29/ \
    lib64/vndk-29/[email protected]; do
    adb shell chcon u:object_r:system_lib_file:s0 "/system/$i"

If you opted to keep the system_b partition, now you copy the contents of the system_a partition over to the other.

adb shell umount /system_root
adb shell dd if=/dev/block/sda33 of=/dev/block/sda34
  1. Copy ADB key to device

Now, we copy the ADB public key for the PC to the device so that we can get output from the device while it’s booting for debugging, as well as getting a shell if we need to.

adb shell mkdir -p /data/misc/adb
adb push ~/.android/ /data/misc/adb/adb_keys
  1. Reboot into Android

Now we just tell the device to reboot through ADB.

adb reboot


Not powered by WordPress or a CMS.

View the code